基于CFD高精度算法的雷电电磁场研究

雷电空间电磁场一直是电磁领域研究的热门，成熟的算法例如有限时域差分法（FDTD），传输线矩阵法（TLM）以及频域的矩量法（MoM）在计算雷电问题方面都有广泛的应用。由于计算流体力学（CFD）中的Euler方程与电磁学中的Maxwell方程有着相同的守恒形式，而且采用间断伽辽金方法（DG）已经在流场问题上得到广泛的尝试，因此引入了基于计算流体力学的DG方法来离散时域Maxwell方程，并采用网格分区并行技术加速计算，使用基于DG的圆球雷达散射截面积（RCS）算例进行测试，数值结果一致表明DG算法在求解电磁场问题上的可行性，之后通过计算一段近场雷电通道的电场分布并与解析解、某算法仿真解对比，数据基本吻合，说明该方法适合于雷电电磁场的计算。     

Cutting path-dependent machinability of SiCp/Al composite under multi-step ultra-precision diamond cutting

Particle-tool interactions, which govern the synergetic deformation of SiC particle reinforced Al matrix composites under mechanical machining, strongly depend on the geometry of particle position residing on cutting path. In the present work, we investigate the influence of cutting path on the machinability of a SiCp/Al composite in multi-step ultra-precision diamond cutting by combining finite element simulations with experimental observations and characterization. Be consistent with experimentally characterized microstructures, the simulated SiCp/Al composite is considered to be composed of randomly distributed polygonally-shaped SiC particles with a volume fraction of 25vol%. A multi-step cutting strategy with depths of cut ranging from 2 to 10 μm is adopted to achieve an ultimate depth of cut of 10 μm. Intrinsic material parameters and extrinsic cutting conditions utilized in finite element simulations of SiCp/Al cutting are consistent with those used in corresponding experiments. Simulation results reveal different particle-tool interactions and failure modes of SiC particles, as well as their correlations with machining force evolution, residual stress distribution and machined surface topography. A detailed comparison between numerical simulation results and experimental data of multi-step diamond cutting of SiCp/Al composite reveals a substantial impact of the number of cutting steps on particle-tool interactions and machined surface quality. These findings provide guidelines for achieving high surface finish of SiCp/Al composites by ultra-precision diamond cutting.     

激光陀螺背向散射研究综述

背向散射直接影响激光陀螺的锁区，是阻碍激光陀螺精度提升的主要因素之一。首先，阐述了背向散射与锁区的联系，介绍了背向散射的成因、分类及分析方法。其次，简述了背向散射的检测方法和抑制措施。最后，对背向散射研究现状进行了总结，并对未来发展进行了探讨。研究成果可指导激光陀螺研制过程中的背向散射控制，有助于提升激光陀螺精度水平。     

Solar sailing in realistic mode,based on a locally-optimal control laws

Ballistic design of solar sailing missions in the solar system is composed of defining the design parameters, the control programs, and the trajectories that provide performance goals of a flight. The use of a solar sail spacecraft imposes specific restrictions on mission parameters that include the degradation limit on the flight duration, the maximum temperature of solar sail's surface, the minimum distance from the Sun, the maximum angular velocity of the spacecraft's rotation and others.Many authors considered the impact of these restrictions on the design of the mission separately, but they used a sophisticated method of finding the exact optimal motion control or applied the most straightforward laws of motion control. This paper uses local-optimal control laws at the complete mathematical models of motion and functioning of solar sail spacecraft to describe a technique of designing interplanetary missions. The described method avoids the need to obtain an accurate optimal solution to the control problem and does not cause significant computational difficulties.     

详细化学反应机理对预混丙烷钝体熄火模拟影响

航空发动机熄火预测是重要关键问题之一，湍流和化学反应的非线性相互作用使预测非常困难。本文采用大涡模拟（LES）对湍流进行高精度模拟，采用概率密度函数输运方程湍流燃烧模型（TPDF）耦合JL4、Z66和H73三种化学反应机理，对预混丙烷钝体熄火现象和规律进行研究。JL4的反应机理最简单，反应释热快，局部放热高，火焰宽度大，火焰两侧温度梯度大，燃烧更加趋于稳定，无法模拟出熄火状态。H73机理绝热火焰温度低，火焰温度低，回流区中部OH含量高；在近熄火状态，大量CO被氧化，释放热量过高导致无法模拟出熄火现象。Z66机理可以模拟出火焰正常状态，在低当量比下也可以模拟出熄火状态。本文算例中，局部Da数大于1的区域超过35%则会发生熄火。     

Initiation characteristics of oblique detonation waves from a finite wedge under argon dilution

In this paper, the flow field characteristics of Oblique Detonation Waves (ODWs) induced by a finite wedge under argon dilution are studied by solving the Euler equations with a detailed chemical model of hydrogen and air. First, the effects of the expansion waves, argon concentration, geometric parameters, and Mach number on the ODW are discussed. The results show that the changes of these parameters may make the oblique detonation not be initiated. Then, the ODW initiation criterion of the finite wedge is summarized, as the characteristic length of the induction zone L_C and the characteristic length of the oblique wedge L_W meet the condition L_C/L_W < 1, the initiation of the ODW occurs; otherwise, it does not occur. What’s more, the Constant Volume Combustion (CVC) theory is applied to study the characteristic length of induction zone. It is found that CVC theory is more suitable for the “smooth transition” type of ODW flow field, the theoretical and numerical characteristic length in induction regions are in good agreement. This work is of great significance for the design of oblique detonation engines for hypersonic vehicles.     

飞秒激光系统图像调焦装置以及方法

飞秒激光直写技术在复杂三维微结构加工领域具有显著优势，而调焦是否精准直接影响了所加工结构的完整度.提出了在光路中临时置入调焦光源和物的图像调焦技术，通过调节物的位置使其成像面与激光聚焦面一致，从而通过清晰可分辨的成像状态间接反映激光聚焦状态.利用Zemax软件模拟分析了原飞秒激光光路与加入调焦光源和物的调焦光路，二者可实现相同加工物镜后工作距离与良好成像质量，证明了该方法的可行性.通过分析得到该过程的成像误差主要由成像镜头焦深(3.9 μm)引起，我们获得的理想调焦精度可达到1/2焦深以内.设计了单层高度为5 μm的二层圆柱结构，通过多次实验验证了所加工元件高度误差在1.5 μm范围以内，与理论分析一致，满足飞秒激光系统的调焦要求.     

反向交叉眼对单脉冲雷达干扰效果分析及仿真验证

交叉眼干扰被认为是对单脉冲雷达干扰最有效的方式之一。基于雷达方程建立了隔离平台回波下的两点源反向交叉眼干扰模型，推导了交叉眼干扰欺骗角一般性公式，研究了干扰机发射天线间距、干扰平台旋转角和干扰机相对雷达之间距离等参数变化对角度欺骗效果的影响，并依据单脉冲雷达接收机获取角度的信息处理流程，建立了单脉冲雷达接收机仿真模型，对交叉眼数学模型的正确性和局限性进行了分析。研究结果表明：单脉冲雷达越靠近两点源交叉眼干扰机中心线、干扰机两发射天线间距越大、与干扰机距离越近时，角度欺骗效果越好；单脉冲雷达的欺骗角度随着与干扰机距离的接近呈指数式增大；数学模型和仿真模型计算的单脉冲雷达角度误差最大值随干扰机天线与雷达天线中心连线的夹角的增大呈指数化增长。研究可为交叉眼干扰工程设计作参考。     

钛合金表面抗激光涂层损伤特性及热效应影响研究

实验研究了钛合金和高反射型陶瓷涂层材料抗连续型激光烧蚀的损伤及温度分布特性，并从热效应影响角度对比分析了二者在抗激光损伤效果方面的差异性。研究结果表明：相比于钛合金，高反射型陶瓷涂层材料能有效增强钛合金基底抗激光损伤的能力；在同等激光功率密度辐照下，陶瓷涂层材料能有效提升钛合金基底耐受激光辐照的时间长度。实验结果表明该陶瓷涂层材料的激光损伤阈值比钛合金高约5.8倍。实验发现陶瓷涂层温升速率高于钛合金，但由于陶瓷材料具有较高的反射特性，以及良好的热吸收和热传导特性，因此能使由激光辐照产生的热量在其表面较快地扩散，而降低向基底方向传导的程度，最终提升陶瓷涂层的抗激光损伤阈值。     

航天器姿态大角度机动有限时间控制

针对航天器姿态大角度机动控制问题，在存在外部扰动的情况下，基于航天器姿态跟踪系统的标准级联特性，利用反步法和自适应控制设计有限时间控制器。提出的控制方法可以严格保证姿态大角度机动系统是全局有限时间稳定的。李雅普诺夫理论推导和仿真结果表明，系统在控制器的作用下可以快速机动到平衡点并保持稳定，全物理仿真试验进一步表明了所提出的控制方法的有效性和优越性。